South-Eastern Asia: Numerically Controlled Lathe Market 2020

Numerically Controlled Lathe Market Size in South-Eastern Asia

The revenue of the numerically controlled lathe market in South-Eastern Asia amounted to $X in 2017, increasing by X% against the previous year. The total market indicated a strong increase from 2007 to 2017: its value increased at an average annual rate of +X% over the last decade. The trend pattern, however, indicated some noticeable fluctuations throughout the analyzed period. Based on 2017 figures, the numerically controlled lathe consumption decreased by -X% against 2015 indices. The growth pace was the most rapid in 2008, with an increase of X% year-to-year. The level of numerically controlled lathe consumption peaked of $X in 2015; however, from 2016 to 2017, it stood at a somewhat lower level.

Numerically Controlled Lathe Production in South-Eastern Asia

In 2017, numerically controlled lathe production in South-Eastern Asia amounted to X units, surging by X% against the previous year. The total output volume increased an average annual rate of +X% over the period from 2007 to 2017; the trend pattern remained relatively stable, with only minor fluctuations being observed throughout the analyzed period. The pace of growth appeared the most rapid in 2008, when it surged by X% y-o-y. The volume of numerically controlled lathe production peaked in 2017, and is expected to retain its growth in the near future.

Numerically Controlled Lathe Exports in South-Eastern Asia

In 2017, numerically controlled lathe exports in South-Eastern Asia amounted to X units, coming down by -X% against the previous year. The numerically controlled lathe exports continue to indicate a remarkable expansion. The most prominent rate of growth was recorded in 2011, when it surged by X% year-to-year. The volume of exports peaked of X units in 2016, and then declined slightly in the following year.

In value terms, numerically controlled lathe exports amounted to $X in 2017. The numerically controlled lathe exports continue to indicate a remarkable growth. Over the period under review, the numerically controlled lathe exports reached its maximum level of $X in 2016, and then declined slightly in the following year.

Numerically Controlled Lathe Exports by Country in South-Eastern Asia

Thailand represented the key exporting country with an export of around X units, which resulted at X% of total exports. It was distantly followed by Singapore (X units), mixed up X% share of total exports. Malaysia (X units) took the slight share of total exports.

Exports from Thailand increased at an average annual rate of +X% from 2007 to 2017. At the same time, Malaysia (+X%) displayed positive paces of growth. Moreover, Malaysia emerged as the fastest growing exporter in South-Eastern Asia, with a CAGR of +X% from 2007-2017. By contrast, Singapore (-X%) illustrated a downward trend over the same period. Singapore (X%) significantly strengthened its position in terms of the global exports, while Malaysia and Thailand saw its share reduced by -X% and -X% from 2007 to 2017, respectively.

In value terms, Thailand ($X) remains the largest numerically controlled lathe supplier in South-Eastern Asia, making up X% of global exports. The second position in the ranking was occupied by Singapore ($X), with a X% share of global exports. It was followed by Malaysia, with a X% share.

In Thailand, numerically controlled lathe exports increased at an average annual rate of +X% over the period from 2007-2017. In the other countries, the average annual rates were as follows: Singapore (-X% per year) and Malaysia (+X% per year).

Numerically Controlled Lathe Export Prices by Country in South-Eastern Asia

The numerically controlled lathe export price in South-Eastern Asia stood at $X thousand per unit in 2017, increasing by X% against the previous year. The numerically controlled lathe export price continues to indicate a temperate contraction. The most prominent rate of growth was recorded in 2017, an increase of X% year-to-year. Over the period under review, the export prices for numerically controlled horizontal lathes, turning centres, for removing metal reached its peak figure level of $X thousand per unit in 2009; however, from 2010 to 2017, it stood at a somewhat lower level.

Export prices varied noticeably by the country of destination; the country with the highest export price was Thailand ($X thousand per unit), while Malaysia ($X thousand per unit) was amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of export prices was attained by Malaysia (+X% per year), while the other leaders experienced a decline in the export price figures.

Numerically Controlled Lathe Imports in South-Eastern Asia

In 2017, the amount of numerically controlled horizontal lathes, turning centres, for removing metal imported in South-Eastern Asia stood at X units, going up by X% against the previous year. The numerically controlled lathe imports continue to indicate a measured growth. The most prominent rate of growth was recorded in 2011, when it surged by X% year-to-year. Over the period under review, the numerically controlled lathe imports reached its peak figure volume of X units in 2012; however, from 2013 to 2017, it stood at a somewhat lower level.

In value terms, numerically controlled lathe imports totaled $X in 2017. The numerically controlled lathe imports continue to indicate a strong expansion. In that year, the numerically controlled lathe imports attained their peak level of $X. From 2013 to 2017, growth of the numerically controlled lathe imports stood at a somewhat lower level.

Numerically Controlled Lathe Imports by Country in South-Eastern Asia

In 2017, Thailand (X units), distantly followed by Vietnam (X units), Malaysia (X units), the Philippines (X units), Singapore (X units) and Indonesia (X units) represented the main importers of numerically controlled horizontal lathes, turning centres, for removing metal, together making up X% of total imports.

From 2007 to 2017, the most notable rate of growth in terms of imports, amongst the main importing countries, was attained by Vietnam (+X% per year), while the other leaders experienced more modest paces of growth.

In value terms, the largest numerically controlled lathe markets worldwide were Thailand ($X), Vietnam ($X) and Malaysia ($X), together comprising X% of total imports.

In terms of the main importing countries , Vietnam (+X% per year) experienced the highest rates of growth with regard to imports, over the last decade, while the other leaders experienced more modest paces of growth.

Numerically Controlled Lathe Import Prices by Country in South-Eastern Asia

In 2017, the numerically controlled lathe import price in South-Eastern Asia amounted to $X thousand per unit, increasing by X% against the previous year. Over the last decade, it increased at an average annual rate of +X%. The most prominent rate of growth was recorded in 2012, when it surged by X% year-to-year. In that year, the import prices for numerically controlled horizontal lathes, turning centres, for removing metal attained their peak level of $X thousand per unit. From 2013 to 2017, growth of the import prices for numerically controlled horizontal lathes, turning centres, for removing metal failed to regain its momentum.

Average import prices varied somewhat amongst the major importing countries. In 2017, major importing countries recorded the following import prices: in Indonesia ($X thousand per unit) and Vietnam ($X thousand per unit), while the Philippines ($X thousand per unit) and Thailand ($X thousand per unit) were amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of import prices was attained by Singapore (+X% per year), while the other leaders experienced more modest paces of growth.

Source: IndexBox Platform